- #82357b gpib to usb driver driver#
- #82357b gpib to usb driver software#
- #82357b gpib to usb driver windows#
#82357b gpib to usb driver windows#
Windows will notify you if a solution is available. So you can just do a simple check for the number being greater than or equal to 0 see if it has been found.ħ error "Paris 7.2. of work and has been closed." A problem with the application to stop functioning properly. The first attached VI is my original request where I found the problems described and the second contains what I have tried to correctĪutoindexing if your friend here (and MUCH simpler because of things).Īlso know that "offset after match" will be-1 if the word was not found. I find the my table has continued to add new entries every time that my for loop runs so I try to reset the table with constant strings at the beginning, but I guess that I did not it properly because I have the same problem.Īnd I also have another problem: my array of words has its size = 7 and if I fill it with fewer words it's size, empty boxes in the results table appear as noted. I did my version of the block diagram (I have attached to it), but I noticed that it only works only the first time I run the VI, subsequently, it displays the same results despite the entry of text or words. I have the front of my VI, an area of input text and two arrays of strings: one that contains a few words I have to say if they can be found in the text.Īnd the other table contains the results of research: found or not found I am a beginner in labview and I have some problems with my application. Problem with an application of text analysis If Apple has a site update, you can check that first. Your player (if any) Java is not indicated clearly in your list of plugins, and your FlashDrive is several versions behind. See above - there known problems with these applications? Their customer support says that it may be the problem with the application Java and Adobe Flash Player Since the recent upgrade, I don't see any of my projects in Shutterfly. Architecture of producer/consumer if you pass the data to another loop via a queue would be a way. If it's fast enough, use a different method to save the data. I suggest you delete the entry in the file of the measurement of the loop to see how long takes of the instrument. Yes, you get a voltage reading and a current reading with each iteration and the number of bytes read is so that you can get a complete reading. The rate at which you can run the VI is dependent on the instrument/GPIB bus and use of Scripture on a Measurment file.
#82357b gpib to usb driver driver#
How many points will be acquired whenever the read.vi is run? That depends on the set 'count bytes' in vi or a single point anything? Are there other ways to get the data more efficiently? (want to write your own driver etc.) Any help would be much appreciated. I had some confusion as below: no I have gained a point each time the while loop is executed? If so, I guess that the time for each loop (and therefore my data rate) depends on my operating system and the computer I have. It's my first time to the instrument control and I just had a little experience in the acquisition of data before.
The problem I have is that I can only save data in ~ 10 HZ then that what I need is at least 200 HZ. (just for the starter, not a good sense, though) Please see the attachment. And I used the instrument for Agilent 66XX driver I downloaded from OR.įor reading continuous data, I put the read.vi in a while loop and data saved by writing in the file lvm. Agilent 82357 A GPIB-USB interface is used to connect the power to the computer. I would like to save the output in more than 200 HZ to my power supply CC 6674 A Agilent with LabVIEW 8.2. Streaming (record) data of Agilent 6674 interface GPIB-USB powered If I run the interactive command of VISA, I got the following error:Ĭannot find the resource by using expression? " » If I plug the converter to the instrument, the function of resource VISA finds return nothing. If I unplugged the converter USB/GPIB instrument, the VISA to find the function return resource: GPIB0::INTFC, COM3, COM4, LPT1 COM7 J' made a small application with the VISA resource find included J' installed MAX, and I can communicate with the VISA test panel using the GPIB-USB converter. I did the following tests on the target computer:
I followed the advice given by OR when you use a converter USB GPIB of Agilent (Tulip active.)
The application works with USB, RS232 and Ethernet interfaces, but I don't see the GPIB interface in the control of VISA resource name. I have deployed the application using the Installer application on the target computer Builder. On my development PC, I can communicate with my instrument using a 82357 B Agilent GPIB - USB converter, without any problem.
#82357b gpib to usb driver software#
I am developing software that communicates with an instrument, with USB, RS232, Ethernet and GPIB interface Agilent 82357 B GPIB/USB, problem with distributed applications
0 kommentar(er)
